1. Cuttings Tie Lotus
Steps
1. When cutting iron wire, you need to choose a slightly tender branch and avoid completely lignified branches. Because slightly tender branches are more sensitive to the stimulation of rooting powder and are more prone to root.
(Author: Drink too much Source: Taxi Walk)
2. Cut the branches short, about one node, one or two nodes. Put the branches in a vitamin B solution for 2 hours and take it out. Dry the surface of the surface, so that the end of the branch is slightly dipped in root powder and put it in the bag for later use.
(Author: Drink too much Source: Taxi Walk)
3. Put the perlite in the seedling box, dig a small hole on the perlite, and put the iron line lotus branches that need to be cut in.
(Author: Drink too much Source: Taxi Walk)
4. After all the branches are planted, spray water with a nozzle at the seedling box so that the roots of the branches can quickly merge with the perlite.
(Author: Drink too much Source: Taxi Walk)
5. Cover the transparent lid and place the seedling box in the ventilated scattering light to maintain it. It cannot be directly exposed to the sun, otherwise it will easily cause the branches to die. Flowers who do not have a seedling box can also put a plastic bag on it to prevent water from evaporating.
(Author: Drink too much Source: Taxi Walk)
6. Open the lid once in about 2 days to change the breath. At the same time, spray a little vitamin B solution on the leaves with a watering pot, which can ensure that the leaves are moist and can promote rooting.
(Author: Drink too much Source: Taxi Walk)
7. When you see a white root system from the bottom of the small box of the seedling box, you can be transplanted into the flower pot. The transplanted soil can choose perlite, vermiculite, and peat soil to mix well according to the ratio of 1: 1: 1. It can be used as a nutrient soil. After that, you can place it in a place where the sun is shining. Watering is wet and wet.
(Author: SAM_ZHOU Source: Tibetan Flower Pavilion)
2. Cutting triangle plum
Steps
1. You can buy a piece of flower mud from the flower shop. According to the needs of cuttings, you can cut a small cuttings of 2cm, 2cm wide and 4cm high. The mud blocks have good water absorption, moisturizing, and breathability, which is very suitable for cuttings.
(Author: Forgotten Angel)
2. Selected branches that were already lone or semi-wood that year, about 10-15cm in length. Leave 2-3 leaves on the upper part.
3. Insert the processed triangle plum branches into the mud block, insert the depth of about 2/3 of the mud, and then soak the mud blocks in the water. Before cutting, you can soak with 1 % root water for about 1 hour.
(Author: Forgotten Angel)
4. Put the cuttings with cuttings in the tray, cover it with a plastic bottle completely, place it in a place with sufficient scattered light, and pay attention to moisturizing and breathable. Look at the mud pieces frequently. If the mud block is dry and cause the leaves to wither, then quickly pour some water. Only by ensuring that the leaves with intact leaves can take root.
(Author: Forgotten Angel)
5. About 30 days will find that white roots are worn out of the mud block, which proves that the cuttings of the cuttings have survived.
(Author: Forgotten Angel)
6. At this time, you can put the mud block and the rooted boupe plums in the flowerpot. The mud can be placed directly in the flower pot. Root damage. After that, fertilizer every 7-10 days can promote the growth of the bougainvillea.
3. Cutting Africa 插
Steps
1. You can choose healthy leaves from the mother plant of Africa for cuttings.
(Author: Golden Linglong King Source: Africa 堇)
2. At the lower end of the picked African blades, cut a knife at the angle of 45 ° obliquely to form a slope, and then soak the lower end of the leaves in the rooted water for about 3 seconds, and take it out to dry.
(Author: Golden Linglong King Source: Africa 堇)
3. While drying the leaves, you can put sand in the flower pot, and then pour a little water.
(Author: Golden Linglong King Source: Africa 堇)
4. Insert the dry African leaves into the sand and place it in a place with sufficient scattered light for maintenance.
(Author: Golden Linglong King Source: Africa 堇)
5. About 20 days, cuttings can take root, and then transplant the African pupa after rooting into the flower pot. Just accept scattered light.
(Author: Golden Linglong King Source: Africa 堇)
4. Cuttings hydraulous flowers
Steps
1. Choose cuttings branches. The cuttings must be selected from those who grow healthy, seemingly green, and a little hard semi -wood branches, which are the best close to the roots. It is best to cut it off in the morning, and then use a small brush to brush the soil and coverage on the branches.
2. trim the cuttings with scissors. At least one node is retained on each branch. The lower end of the node is kept at least 3-5cm. It is best to keep a pair of leaves, which can help photosynthesis and promote rooting.
3. In order to allow the hydrangea to take root as soon as possible, the trimmed branches can be placed in the root of the roots for about 3 seconds, or soaked in the water with willow branches in the water.
4. The soil of cutting can be mixed with peat soil and perlite at a ratio of 1: 1. Fill the soil in the seedling box, then place it in a tray filled with water, soak for more than 30 minutes to ensure that the soil in the seedling box is soaked, and there must be no dry places. 5. Insert 3-5cm at the end of the hydrangea branch node into the soil. Try not to contact each other between the leaves, otherwise the leaves will be prone to rot infection.
6. Put the seedling box in a place where the sunlight cannot be directly shot and ventilated. During this period, spray it, spray water 1-2 times a week, and keep the soil moist. After about 3 weeks, you start to grow root.
7. The method of judging whether to take root is: gently pull up with your hands. If you feel the resistance, it means that the hydrangea has long roots and can be transferred from the seedling box to the flower pot. Then put it in a semi-yin environment to keep the pot soil wet, and can be poured every 10-15 days.
5. Cutting Dayan Tong
Steps
1. Cut a leaf from the mother plant of the big rock tung with a knife, it is best to cut it down at 45 °.
(Author: oolong ball Source: Taxi Wing)
2. Like the usual cut vegetables, cut the cut large rock tung leaves into small pieces.
(Author: oolong ball Source: Taxi Wing)
3. Cuttings can choose sand, vermiculite or peat soil. Bury into the leaves of the big rock tung, the height of the buried height is about 1/2 of the blades, and then cover the lid to moisturize and place it in the place where the scattered light can be illuminated.
(Author: oolong ball Source: Taxi Wing)
4. After about half a month, the cuttings of the cuttings can take root. After rooting, it can be transferred to the flower pot and placed in a living room with good scattered light or on the east balcony. There are a lot of fluff on the leaves of the big rock tung. When watering and fertilizing, be careful not to get on the leaves, otherwise the leaves will rot.
(Author: oolong ball Source: Taxi Wing)
The cutting method introduced by Huahua,
Is it particularly simple?
You may wish to take advantage of the weather,
Come a wave of cuttings.
